InQor DC-DC Converters
    SynQor’s ruggedized DC-DC converters... the power behind industry
InQor Series Isolated DC-DC Converters The InQor® Series dc-dc converter are composed of next-generation, board-mountable, isolated, fixed switching frequency dc-dc converters that use synchronous rectification to achieve extremely high power conversion efficiency. Each module is supplied completely encased to provide protection from the harsh environments seen in many industrial and transportation applications.
Product Links
Product Part Numbering Convention
Product Part Numbering Convention
Quarter-Brick
 
InQor Encased Mechanical Drawing
 
Click on the images to enlarge them
(will open a new window)
 NOTES
   1) Pins 1-3, 5-7 are 0.040" (1.02mm) diameter with 0.080" (2.03 mm) diameter standoff shoulders.
   2) Pins 4 and 8 are 0.062" (1.57 mm) diameter with 0.100" (2.54 mm) diameter standoff shoulders.
   3) Recommended pin length is 0.03" (0.76mm) greater than the PCB thickness.
   4) All Pins: Material - Copper Alloy; Finish - Matte Tin over Nickel plate
   5) Undimensioned components shown are for visual reference only.
   6) Weight: 3.02 oz (85.7 g)
   7) All dimensions in inches (mm)
        Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
                            x.xxx +/-0.010 in. (x.xx +/-0.25mm)
   8) Workmanship: Meets or exceeds IPC-A-610C Class II
   9) UL/TUV standards require a clearance greater than 0.04" (1.02mm) between input and output for Basic insulation. This issue should be considered if any copper traces are on the top side of the user's board. Note that the ferrite cores are considered part of the input/primary circuit.
  10) M3 screws used to bolt unit's baseplate to other surfaces (such as a heatsink) must not exceed 0.100" (2.54 mm) depth below the surface of the baseplate.
  11) Applied torque per screw should not exceed 6in-lb (0.7 Nm).
  12) Baseplate flatness tolerance is 0.004" (.10mm) TIR for surface.

 PIN-OUT         See InQor Converters Pin-Out description
Half-Brick (Exa and Zeta)
 
InQor Encased Mechanical Drawing
 
Click on the images to enlarge them
(will open a new window)
 NOTES
   1) Applied torque per screw should not exceed 6in-lb.(0.7 Nm)
   2) Baseplate flatness tolerance is 0.004" (0.10 mm) TIR for surface
   3) Pins 1, 2, 4, 6-8, are 0.040" (1.02mm) diameter with 0.080" (2.03 mm) diameter standoff shoulders
   4) Pins 5, 9 are 0.080" (2.03 mm) diameter shoulderless pins.
   5) All Pins: Material - Copper Alloy; Finish - Matte Tin over Nickel plate
   6) Undimensioned components are shown for visualreference only.
   7) Weight: 4.3 oz. (123 g) typical
   8) All dimensions in inches (mm)
        Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
                            x.xxx +/-0.010 in. (x.xx +/-0.25mm)
   9) Workmanship: Meets or exceeds IPC-A-610C Class II

 PIN-OUT         See InQor Converters Pin-Out description
Half-Brick (Peta)
 
InQor Encased Mechanical Drawing
 
Click on the images to enlarge them
(will open a new window)
 NOTES
   1) Pins 1-3, 5-7 are 0.040" (1.02 mm) diameter with 0.080" (2.03 mm) diameter standoff shoulders.
   2) Pins 4 and 8 are 0.080” (2.03 mm) diameter with 0.125” (3.18 mm) diameter standoff shoulders.
   3) Recommended pin length is 0.03" (0.76 mm) greater than the PCB thickness.
   4) All Pins: Material - Copper Alloy; Finish - Matte Tin over Nickel plate
   5) Weight: 5 oz. (142 g) typical
   6) All dimensions in inches (mm)
        Tolerances: x.xx +/-0.02 in. (x.x +/-0.5mm)
                            x.xxx +/-0.010 in. (x.xx +/-0.25mm)
   7) Workmanship: Meets or exceeds IPC-A-610C Class II
   8) Applied torque per screw should not exceed 6in-lb.
        (0.7 Nm).
   9) Baseplate flatness tolerance is 0.004" (.10 mm) TIR for surface.

 PIN-OUT         See InQor Converters Pin-Out description